WEIMA WL-4S Vertical Hopper Fed Low Noise Grinder Specifications: \n\n-- 23-1/2" x 31-1/2" (600 mm - 800 mm) hopper opening at the top, 0.8 cu. yds. (0.6 cu. m) cap.; \n\n-- 30 HP Motor w/hydraulic clutch, 14-1/2" dia. rotor grinds at 90 RPM. \n\n-- Patented "V-Rotor" design utilizes a V-groove rotor closely matched to grooves in the counter-knife to ensure uniform discharge free of splinters, reduce friction, and dedicate more horsepower to grin

WEIMA WL 4S

Weima

ExFactory

CEFLA PRE / IRM TTE 3000 Infrared Preheat Oven: \n\n-- Overall dimensions: 1,300 mm (51" wide) x 3,000 mm (118.11") long. \n\n--÷ This unit has three (3) IR LAMPS to add heat to the substrate before entering the spray booth to make sure to have and even coat of finishing coating for consistence.

CEFLA PRE / IRM TTE 3000

Cefla

GIARDINA Jet-hot Air Drying Tunnel "GP-JET-10" 40 foot long oven General Description; The air is taken externally by means of a plenum, which is equipped with filtering panels, and it is warmed by heat exchanger with finned copper/aluminium spiral pipes. It operates with recirculating movement, the solvent exhaust is achieved through over-pressure and it is controlled by gates in order to ensure air exchange and remove solvents from the building.

GIARDINA GP JET 10

GIARDINA

DODD'S C-48J DRAWER CLAMP \n\n-- Heavy-Duty vertical universal Drawer Box Clamp with fixed left jaw and motorized adjustable right clamping jaw. \n\n-- The operator loads a drawer front &amp; pair of sides into the clamp, then activates the clamping head with push button control. Then the jaws retract and the drawer bottom &amp; back are installed. The Clamp is activated once again to complete the box assembly. \n\n-- 2" - 15" Drawer height, 6" -

DODDS C-48J

Dodds SE 15 S Dovetailer with (15) Spindles. (15) Spindles, 3 HP - 3,850 RPM motor, 10,500 RPM spindle speed; Specifications: \n\n-- 0.5 HP Feed cycle motor, automatic or÷manual cycling selection, (10 - 25) strokes/Min. \n\n-- Ball bearing spindles in an oil mist lubrication system, adjustable chip breakers. \n\n-- Cuts all (4) corners, dovetails drawer fronts-and-backs or drawer sides in pairs; (2) "quick changeover" cams (1/2" and 5/8") for eas

DODDS SE 15 S

Sierra, 12" bore diameter x 120 length, auto cycle, conveyor, smog hog, coolant,. tooling, 1989

Surplus Record

Sierra #M111, 8-1/2" bore x 125 length, serial #908008, 1983

# 1. Felder BF6-31: 
5 operation machine with all components/ attachments: 3 PH. 
Sliding Table Saw, Tilted Shaper (3/4" &amp; 1 1/4" spindle), 12" Planer (4 knifes) 
12" Jointer (4 knifes) Motion table Mortiser. Including Dust Collector. Made in Austria. (Paid 25 K plus) Asking $ 12500, best offer will be considered. Time for the next generation.

Felder BF6-31

Felder

A-Z Woodcrafters Inc.

SPROUT 21 Inch Pellet Mill, Complete with the following features and components: \n\n-- Door Centri-Feeder (Force Feeder). \n\n-- Belt Drive. \n\n-- 3-Roll configuration. NOTES: ● No Conditioner. ● No Main Drive Motor.

SPROUT 21V

WEINIG RONDAMAT 960 Profile And Straight Knife Grinder with Automatic Mode for profile knives, Variable Frequency Controlled Drive spindle speed- 1000-3000 RPM (increments of 100) Drive Motor: 1.5 HP \n\n--Template Carrier: Utilizes a template- stylus-copy system, whereby the tool head table copying-grinding is effortless (precision linear floating table movement feels smooth as if there is zero gravity). Resistance template cross support with se

WEINIG R 960

WEINIG

WEINIG Rondamat 960

VECOPLAN VAZ 2000 M-N SP Wood Waste Grinder Heavy-duty, Single shaft, high output "TorsionPoint" cutting rotor. Low speed / High torque design with low RPM and noise. Heavy Spherical Roller Bearings in a stress-free frame that is robotically welded. Specifications: \n\n-- Machine In-feed Opening 78" x 78" \n\n-- Hopper Volume 11.9 cu/yds \n\n--Rotor Diameter 25" \n\n-- Number of Cutters 186, 4-way indexable \n\n-- Rotor Speed 30 - 200 RPM via Spe

VECOPLAN VAZ 2000 M-N SP

VECOPLAN

WENGER Conditioner or Pre-Conditioner complete with the following features: \n\n-- Horizontal Twin Shaft Differential Diameter Cylinder (DDC) arrangement. \n\n-- Stainless Steel construction. \n\n-- 20 HP Drive Motor. \n\n-- Approximate 42" wide x 120" long elliptical cylinder with top & bottom steam injection. \n\n-- Approximate 11" x 11" inlet, 10" x 10" outlet. \n\n-- Removed from service and ready to load.

WENGER 66460-10

Wenger

BLISS CounterFlow Pellet Cooler with the following features: \n\n-- Rated for 5 to 7 TPH. \n\n-- Includes Cooler, \n\n-- Stainless steel Cyclone, \n\n-- Airlocks, and Fan, \n\n-- Takeaway Drag Conveyor.

BLISS 6-74-6

Bliss

WEINIG RONDAMAT R960 Powerlock Profile Tool Grinder -- Working dimensions 9-3/8" max. cutterhead length, tool dia. 3-15/16" to 11-13/16".\n\n--Specifications\n\n-- Motor: Inverter controled grinding wheel speed of 1,500 - 3,000 RPM with 1.5 HP motor.\n\n-- Productivity package: Machine light, back clearance angle motorized; grinding wheel advance motorized; setting of side clearance angle pneumatically.\n\n-- Tool carriage movement with precision

PRS MISCELLANEOUS Pallet Stacker. \n\n-- This pallet stacker will stack broken, tear down and odd size pallets that can vary up to 12" in either the stringer or deck board length. \n\n-- This unique machine stacks like a fork truck. Uses 48" length forks that travel in / out of the pallets. \n\n-- A scissor lift platform doing the lifting. \n\n-- Ideal if placed near the operator for stacking odd size pallets that would otherwise be hand stacked.

PRS PALLET STACKER

NORTHFIELD 12HD JOINTER 12" Width cap. &amp; 5/8" max. depth of cut, 3 HP - 3,600 TEFC motor Belt drive 4-1/4" dia. cutterhead @ 6,000 RPM, 3-knife cutterhead with high speed steel knives. \n\n-- 12" x 96" cast iron table with 17" wide rear table section, 31-1/2" table height; 5-1/2" x 52" fence tilts 0ø - 45ø, 5/8" x 12" rabbeting cap. \n\n-- Complete with: Swing-away cutterhead guard, magnetic controls and 3-leg supports to avoid rocking.

NORTHFIELD 12HD

Northfield

BURKLE TRUV1300/4 4-Lamp UV ovens, 51" Width Capacity Equipped with (4) 51" long Mercury UltraViolet Lamps. Specifications: \n\n-- Lamps 1 &amp; 4 dual power 80/120 Watts and lamps 2 &amp; 3 single power 80 W, Temperature controlled ventilation cooling/fumes exhaust for each pair of lamps. \n\n-- Variable feed speed conveyor from 20 - 140 FPM, \n\n-- Free-standing electrical cabinet with light indicators, amp meters and lamp run time indicators. 

BURKLE TRUV 1300/4 FOUR LAMP

Bürkle

LARICK 410 Shape and Sand Single sided Profile Shape and Sand with (1) Shaper and (2) Disc Sanders. Great for raised panel doors and a wide variety of workpieces. \n\n-- Feed through machine with: (1) 7.5 HP Shaping station with floating head and variable speeds from 4,000 to 7,000 RPM with inverter control from key pad; 1-1/4" spindle with 4" to 7' dia. cutterhead capacity, horizontal &amp; vertical adjustments with position indication. \n\n-- (

LARICK 410

GLOBAL FINISHING SYSTEMS Batch Oven. This Oven is designed to take in outside air and also mix with recirculated air for the drying cycle. This Ovens inside working dimensions are 20' (240") x 12' (144") with a ceiling height of 10' (120") Booth is built on a I-Beam structure as seen in the attached drawings.\n\n--Walls are fabricated using 18 gauge galvanized steel pre punched and companion flanged for bolt together assembly.\n\n--booths support

GLOBAL FINISHING DE-121020-T-DT-S

Global

MAKOR 9-LAMP UV OVEN, model FTL/HE U.V. \n\n-- Curing oven is a flexible and effective system for the UV curing of linear parts.The machine features (3) bottom cure units with dual (double length lamps) for top and side curing. ~~ Includes PLC control with lamp power adjustment and feed speed control. ~~ Product Specification: 8" Width x 4" height cap.; feed through system for immediate curing of linear profiled material, designed for curing of t

MAKOR FTL/HE

Makor

WYSONG &amp; MILLS 600 and 601 Dovertailers 2-Machine system for both male &amp; female dovetails; 15" max. material width. Extremely clean machines ...a rare find! Specifications: \n\n-- Each unit with: (15) 6,000 RPM Spindle heads, 1" spindle centers, 5 HP - 3,850 RPM motor; \n\n-- Variable feed/cycle for up to (25) strokes/Min, 0.25 HP feed drive on model "600"; and 0.5 HP feed drive on model "601". \n\n-- Complete with: Chipbreaker, oil bath 

WYSONG &amp; MILES 600 &amp; 601

Wysong

VOORWOOD A 12 Automatic Miter Lock Shaper The A 12 Miter Lock Shaper does profiles precision miter lock joints from 90° to 150° in solid wood and plywood substrate in one pass. Machine only requires one cutter to mill both sides of the miter lock joint Features: \n\n-- Shaper spindle is 5.25 (133.4 mm) long, and equipped with vertical, horizontal and tilt adjustments. \n\n-- The tool can be rotated from 0 to 120 degrees allowing the operator to m

VOORWOOD A 12

Voorwood

Hammermill, hog, grinder, and blower; 10" inlet; 40HP; 3Phase; Dual voltage (230/460) Reliance motor; (3) sets of bolt down slot-style hammer teeth in varying conditions; 8" blower outlet.

MONTGOMERY 10 MAX

MONTGOMERY

NORTHFIELD 12MD Jointer w/ Byrd Helical Head Specifications: Motor: Direct drive 5 HP Table: 74" overall length, 10" width Fence: 45" x 5-1/4", tilts to 45, cut depth gauge Cutter Head: Byrd 12" Helical Cutter Head w/ 6" Dust chute.

NORTHFIELD 12MD

SUPERFICI ELMAG TTI-13 UV Oven for 3-D Curing; Equipped with (3) Lamps, (2) top and (1) bottom lamp. Specifications: \n\n-- 1,600 mm (60 ") Working width and equipped with (3) UltraViolet Lamps 40 / 80 Watts/cm. (power being confirmed) \n\n-- Temperature controlled ventilation cooling/fumes exhaust for each lamps. \n\n-- Suitable for mercury and gallium lamps. \n\n-- Approx 1,600 mm (63") wide conveyor Total length 2,500 mm (98"). (dimensions bei

SUPERFICI / ELMAG TTI-13

Superfici

DODDS SE 20-00 Dovetailer (20) Spindles, 1-3/4" max. material thickness &amp; 20" max. material width; Specifications: \n\n-- 10 HP -motor, precision movement of spindle assembly with adjustable carriage stroke feed (10 - 25) movements/Min, foot pedal control to engage cutting cycle mode. \n\n-- 8 - 48 in. drawer width left to right, 7 in. minimum drawer depth front to back. \n\n-- Features quick changeover from fronts/backs to sides without chan

DODDS SE 20-00

WEIMA TIGER 400 Horizontal "Slow Speed" Single Shaft Wood Grinder w/Vibratory Conveyor \n\n-- Specifications: 6" High (160 mm) x 15-11/16" (400 mm) wide max. infeed opening, 50 HP rotor motor, 14" dia. rotor grinds at 620 RPM (fixed rotor speed depending on application). \n\n-- Equipped with: Patented "V-ROTOR" design utilizes a v-groove rotor closely matched to grooves in the counter-knife to ensure uniform discharge free of splinters, reduce fr

WEIMA TIGER 400

MIKRON M652R Moulding Shaper&amp; Vertical Router for Curved Mouldings \n\n-- Designed for curved casings, crowns, circles, ellipses and straight mouldings.\n\n--Specifications: \n\n-- Working dimensions: 6" Wide x 7" thickness capacity. \n\n-- Spindle dia. 1-1/4" with cutterhead speed of 6,000 RPM. \n\n-- 6-1/2" Max. cutting circle in horizontal position, 6" max. cutting circle tilted. \n\n-- Feed motor 7.5 HP, variable speed 0 - 30 FPM. \n\n-- 

MIKRON M652R

Mikron

BURKLE 4 Lamp UV ovens, 51" Width cap., \n\n--Equipped with (4) 51" long Ultra Violet lamps. Lamps 1, 2 &amp; 3 are single power 80W, Lamp #4 is dual power 80/120W. \n\n--Temperature controlled ventilation cooling/fumes exhaust for each pair of lamps. \n\n-- Variable feed speed conveyor from 20 - 140 FPM, \n\n-- Free-standing electrical cabinet with light indicators, amp meters and lamp run time indicators. \n\n-- Operator interface control is mo

INDUSTRIAL FINGER JOINTER: MODEL 3870 SHAPER & FJA-100 ASSEMBLY MACHINE: \n\n-- Model 3870 Dual Finger Jointer Shapers with feed chain speeds of 45 FPM via 5 HP fixed speed electric drive. Shaper is furnished with (2) 1-13/16 dia. 10 HP cutterhead spindles and (2) 5 HP trim saw motors and an automatic roll type glue spreader with pressurized glue tank. \n\n-- Production rates are: 60 lugs per minute with lugs on 9" centers and blocks up to 6 wide

INDUSTRIAL 3870 & FJA-100

Baileigh

CADORET Manual Finger Joint System: Shaper Section includes right and left hand Shaper Units, each with AC variable speed drives from 30 to 60 FPM. Features: \n\n-- Shapers with hand-wheels and digital readout scales; on on the horizontal saw adjustment and one each on vertical and horizontal spindle adjustments, \n\n-- Retractable guide knives for running flooring; quick change chain lug back up blocks for end matching. \n\n-- Extended arm for r

CADORET MANUELLE-STD

VECOPLAN VH-14/40 CW Low Noise Grinder with Horizontal Feed \n\n-- Specifications: 14" Wide x 3-1/2" high infeed opening, 30 HP rotor motor with power belt drive. \n\n-- Equipped with: 12" Dia. rotor with 4-way indexable, replaceable carbide cutter knives, 1-piece counter bed knife, rotor/cutterhead grinding speed of 350 - 400 RPM. \n\n-- Features: Top &amp; bottom infeed rollers, Heavy Duty Industrial Grade construction with stress-relieved shel

VECOPLAN VH 14

BREWCO BSBH Super Band Multi-Head Resaw 2-Head horizontal band resaw, with 8"w x 8"h cutting capacity. \n\n-- (2) 20 HP blade drive motors, 28" dia. blade wheels on heavy hubs. Can accept 1", 1-1/4" or 1-1/2" wide bandsaw blades. \n\n-- Variable speed hydraulic feeds from 0 - 90 FPM; 3 HP hydraulic power pack included. \n\n-- Powered top hold down wheels.

BREWCO BSBH

VIKING DUO-MATIC Pallet Assembly System \n\n-- 60" X 60" Pallet capacity, right hand system, 3-stringer. \n\n-- Complete with: Viking stacker and outfeed conveyor. \n\n-- Unit is in operation and available for inspection and completes in an average (8-Hour shift) up to 1,464 pallets per day.

VIKING DUO-MATIC

Viking

METAL WORKS 128-4 / -2 6-Head Resaw (4-Head Plus 2-Head) Metal Works manufactures a full line of saw mill equipment. From our industry leading short log debarker to some of the most dependable band saws on the market. Specifications: \n\n-- 4-Head 128-4 \n\n-- Pallet material 4" to 6".and will have an 8" x 10" cant capacity. \n\n-- Each head has 40" wheels using a 20'-4" length x 1-1/2" blade \n\n-- Each saw has 40 HP electric motor. \n\n-- Varia

METAL WORKS 128-4 / -2

VIKING DUO-MATIC Pallet Assembly System 60" X 60" Pallet capacity, right hand system, 4-stringer. \n\n-- Complete with: Viking stacker and outfeed conveyor. \n\n-- Unit available for inspection.\n\n-- Completes an average of 1,200 to 1,500 pallets per 8 hour shift.

BREWCO BSBH Super Band Multi-Head Resaw. \n\n-- 4-Head BREWCO "Big Band" resaw. \n\n-- 3/4" Minimum to 8" max. cant thickness capacity. \n\n-- 2" Minimum to 8" max. cant width capacity. \n\n-- 28" Solid steel balanced blade wheels. \n\n-- 1-1/4" Wide x 13' 2" long thin kerf blade. \n\n-- 20 HP High efficiency 3-phase industrial motors. \n\n-- Positive feed system with adjustable speed. \n\n-- Heavy duty construction, Made in the USA.

HMC ET-10 Double End Trim Saw Zero saw and controls on right hand end \n\n-- Machine has capability of trimming material from 6' to 16' lengths. \n\n-- 24" Blades with cutting capacity of 9" thickness. Includes: \n\n-- 10 HP Saw motors and waste belt \n\n-- Belt waste conveyor 24" W x 18' L for waste removal underneath the saw unit. \n\n-- Push button setworks.

HMC ET-10

Oven Dimensions (overall): 14' Wide x 26' long x 10' high \n\n-- Utilities - Electrical: 230 or 460 Volt, 3-Phase, 60 Hz \n\n--The Oven will have a 750,000 BTU Burner complete with Gas Train &amp; temperature controllers with a max. temperature of 160 f. \n\n-- Oven enclosure Panels consist of: 20-Gauge, aluminized 4" thick x 12' long x 27 1/2" wide, Heavy interlocking steel tongue &amp; groove panels. \n\n-- There is a 11' 4" opening at each end

FINISHING SYSTEMS 26'L X14'W X 10'H

WEINIG RONDAMAT R960 Profile Grinder. Working Dimensions: 9-29/64" maximum tool width; 3-15/16" Minimum to 11-13/16" Maximum cutting circle \n\n-- Grinding Wheel: Diameter 5-29/32" min to 8-7/8" max. grinding wheel bore - 60 mm. Onboard diamond wheel dressing tool. \n\n-- Drive: Variable Frequency Controlled Drive giving a spindle speed - 1,500 to 3000 RPM; 1.5 HP Motor. \n\n-- Template carrier: Utilizes a template-stylus-copy system, whereby the

Cub Cadet Compact Utility Diesel Tractor W/Loader, 364 Hrs Showing, MFWD, 1.5L Diesel Engine, 32 Hp, Power Shift Series, 833 Front Loader, 5’ Bucket, 3 Point Hitch, 540 PTO, Front 20 X 8.5-12, Rear 10-16.5 NHS, SN: 037501-0D125202

Used Further Machines for sale— 801

WEIMA WL 4S

CEFLA PRE / IRM TTE 3000

GIARDINA GP JET 10

DODDS C-48J

DODDS SE 15 S

Sierra, 12" bore diameter x 120 length, auto cycle, conveyor, smog hog, coolant,. tooling, 1989

Sierra #M111, 8-1/2" bore x 125 length, serial #908008, 1983

Felder BF6-31

SPROUT 21V

WEINIG R 960

VECOPLAN VAZ 2000 M-N SP

WENGER 66460-10

BLISS 6-74-6

WEINIG R 960

PRS PALLET STACKER

NORTHFIELD 12HD

BURKLE TRUV 1300/4 FOUR LAMP

LARICK 410

GLOBAL FINISHING DE-121020-T-DT-S

MAKOR FTL/HE

WYSONG &amp; MILES 600 &amp; 601

VOORWOOD A 12

MONTGOMERY 10 MAX

NORTHFIELD 12MD

SUPERFICI / ELMAG TTI-13

DODDS SE 20-00

WEIMA TIGER 400

MIKRON M652R

BURKLE TRUV 1300/4 FOUR LAMP

INDUSTRIAL 3870 & FJA-100

CADORET MANUELLE-STD

VECOPLAN VH 14

BREWCO BSBH

VIKING DUO-MATIC

METAL WORKS 128-4 / -2

VIKING DUO-MATIC

BREWCO BSBH

HMC ET-10

FINISHING SYSTEMS 26'L X14'W X 10'H

WEINIG R 960

WYSONG & MILES 600 & 601